How To Light Gas Fireplace Pilot

Turn the Control of the Gas Next up turn the control of the gas until the setting of the pilot aligns to the mark located on the outer rim of that control. It measures heat from the pilot flame on the thermocouple and if anything is even slightly off the valve will snap closed and shut off the fire.

Pin By Rodney Maine On Gas Fireplace Troubleshooting In 2021 Gas Fireplace Outdoor Gas Fireplace Fireplace

There are two crucial functions of a pilot light.

How to light gas fireplace pilot. Press this button and you should see the pilot light turn on whenever you turn the gas control to start the gas. If gas is coming out of the pilot but it still wont light the spark igniter could be the problem. There are two easy pilot adjustments that can be made.

If you turn the gas off you have to eventually have to turn it back on. Most fireplaces unless specified otherwise in the manual have a gas control knob which is next to a colored button. Light the flame with a match or long-barreled lighter if there is no piezoelectric control.

Find the Control Dial for the Gas The next step in lighting the pilot for your gas fireplace is to locate the dial for the gas controls. To light gas logs safely turn the control handle to the pilot position press it in light the pilot with a match and hold down the handle for half a minute until the pilots are burning on their own. Pilot light systems are the most common reason gas fireplaces fail to light so check the main gas valve to make sure the gas is turned on.

Read and follow the instructions that came with you. One is to generate electricity. Most gas fireplaces have a standing pilot light which is a small flame that burns even when you arent using the fireplace.

With control knob in push the piezo ignitor in continuously until pilot ignites every 3-5 seconds. Replacement piezo ignitor httpamznto2i7clAn Replacement Thermopile httpamznto2j1sFm3WARNING. If the pilot does not light wait 5 minutes and try again.

Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube. Once pilot flame is lit keep knob pushed in for 60 seconds. Make sure that you push that button in while pushing the starter.

The fireplace gas valve with all the control knobs has a built-in safety mechanism. Keep pushing the button until the pilot light turns on. Once the pilot is lit hold the button down for about 20 seconds until the thermocouple has time to.

The pilot should start immediately once the flame is close enough. Before you go ahead and hit that off switch you should first find out where your pilot light is located. And the second is to ignite the gas once the valve is opened.

If after pushing the button the pilot does not light wait for about 10 seconds before you push the button in again. The process may not be exactly the same for all models for. Once you have given any excess gas a chance to dissipate follow the instructions in your systems manual to relight the pilot.

Some people like to turn this off when the weather warms to conserve gas. Millivolts that close and open your gas valve. Push in knob this releases the gas to the pilot area only.

Often this will involve manually depressing the pilot valve and using an electric ignitor or match to light the pilot. If there is no button present then it. How to turn off your pilot light on a gas fireplace.

If you have an electronic ignition unit using your remote control simply press the on button and the pilot will re-ignite within a few seconds followed by the fireplace a few seconds after that. Re-lighting pilot lights is straightforward on todays modern gas fireplaces. Using a long match or long-barreled lighter press and hold down the gas control knob with the lit match or lighter until the pilot lights.

Keep a close eye on your pilot light once you have restored the flame. Before turning it you should look for an ignition button and check to see if a spark is present when you press it. Light the pilot on a gas-log fireplace by turning the gas flow knob to the pilot setting holding the knob in and using a match to ignite the pilot.

Once the pilot is lit continue to hold the valve knob in for 60 seconds then slowly release. While pressing and holding in the valve knob in PILOT position - it should press in about 14 press the red piezo button repeatedly once per second until the pilot ignites. The pilot should start as soon as the flame is close enough.

After lighting the pilot continue to hold the control knob in for about 30 seconds or the pilot may go out. Release knob if pilot stays lit If not go back to step 3 and repeat. The function of a pilot light.

This makes the fireplace easy to start when its cold outside.

Diy Gas Fireplace Won T Light How To Clean Your Thermopile And Thermocouple Gas Fireplace Clean Fireplace Fireplace

Gas Logs Pilot Light Gas Fireplace Logs Gas Lights Free Gas

How To Light The Pilot On A Gas Fireplace Gas Fireplace Fireplace Lighting Majestic Fireplace

Gas Fireplace Repair My Pilot Won T Stay Lit My Gas Fireplace Repair Gas Fireplace Gas Fireplace Parts Heating Repair

Pilot Lighting For Gas Logs Gas Logs Household Hacks Gas

13 Outstanding Pilot Light Gas Fireplace Photo Idea Gas Fireplace Fireplace Decor

Gas Log Fireplace Repair Tips So Helpful This Link Is How To Troubleshoot When Your Fireplace Keeps Gas Fireplace Napoleon Gas Fireplace Gas Fireplace Logs