Kitchen Cabinet Crown Molding Uneven Ceiling

A starter or riser molding is mounted to the cabinet top in order to simulate an extension of the cabinet box, allowing the crown molding to be installed higher. This will give you a perfect line.

Levelers plastic and metal levelers

Next the crown molding is attached to the carrier piece.

Kitchen cabinet crown molding uneven ceiling. We have approx a 1/2 difference throughout our kitchen, yet all our crown molding (except the 2 shorter cabinets) go all the way to the ceiling.no gaps. Adding a fascia above the lower cabinet provides a place for the lower crown to return even though it’s on the same plane. Provide a nailing surface for crown moulding by attaching solid wood mounting strips to the top edges of the cabinets.

The perimeter of the room is 9’. Plaster work is an art form. Take your scribe tool of choice (i’m using fastcaps accuscribe) and set it at the same distance between the ceiling and the top edge of the crown molding where it is furthest from the ceiling.

When the gap isn’t that big, we’ve scribed the top of the molding to fit the uneven ceiling. Does not fit under the standard height space. Fill the large gaps with wood putty then run a line of paintable caulk.

Our kitchen ceiling is 10’ at the highest point (inside the tray). This gives a varied height above the counter, which looks good and gives additional height for different appliances on the counter which clients find useful when their coffee pot etc. You will need to do a 2 piece molding application:

The crown molding is attached to the ceiling and to a vertical 1 x 3 that runs along the top of the wall cabinets. Position the tip of the pencil at the widest gap and rotate it so the body of the pencil contacts the ceiling. The crown molding will have to ability to 'float' or 'ride' up and down on the carrier molding as needed to always touch the ceiling.

Perhaps, you can use matching baskets to hold otherwise unappealing odds and ends. Crown molding ceiling gap happens because the rough lumber behind the drywall shrinks. If the space you are trying to fill is relatively small, crown molding can be your best friend.

(use one long strip for a row of cabinets the same depth.) then apply wood glue to each strip, nail it in place, and let dry. To do this green tape both the ceiling and the trim in a straight line. The issue with this is you can cut off only so much before it negatively affects the crown molding details.

You’ll see in the picture here that the dip is centered on the molding. Another key point is the outside temperature and humidity is much different in south carolina during the year. If the ceiling above the cabinets is not flat and level, crown moulding will touch the ceiling at one point and have significant gaps at others.

It is usually about 1.5 tall. Continue with this technique around the rest of the kitchen, cutting inside and outside miters at the normal miter angle, and “rolling” the crown up or down so that it meets the vertical height needed to maintain the proper reveal. Some are less straight then others.

You can also raise the 30 unit to the same height as the 42 unit against the ceiling. Do the same on the wall below. This is a common problem in old houses when you install the cabinets to the ceiling.

Saved by evrim icoz photography. Properly installed cabinets are flat and level. Discussion starter • #1 • apr 18, 2009 (edited) hi, im putting crown molding for the first time and am realizing how much more challenging it can be.

Apply and smooth the caulk then remove the tape. Although the cabinet above the microwave is shorter, it becomes a focal point in the room by raising the crown to the ceiling and adding a design element to break up what would otherwise be a large blank surface. To do this green tape both the ceiling and the trim in a straight line.

Glue a 1 riser to the top of the crown, then use this to scribe. Fill the large gaps with wood putty then run a line of paintable caulk. This piece is attached to the top of the cabinets.

Push the molding up till you hit the lowest point of the ceiling. Cabinets to ceiling above kitchen cabinets soffit ideas crown molding moulding ceiling height cabinet doors interior decorating decorating ideas. Using a starter or riser molding in conjunction with a crown molding also provides the ability to better disguise an uneven ceiling, as one end of the crown molding may be mounted higher or lower than the other end along the face of the riser.

This little 1/4 strip should be sprayed black. This piece is attached to the top of the cabinets. We didn’t want our cabinets to go clear up to 9’, so our custom cabinet maker added a soffit that matched the cabinets.

This will give you a perfect line. It all is one continuous piece from the cabinets up to the crown molding. The ceiling height varies by about 1 3/4 inches from one end of the kitchen to the other end (something i should have thought about sooner).

Measure and mark the front section of crown molding to the cabinet width. It works, but doesn’t really look good. Next the crown molding is attached to the carrier piece.

Or, make it a curio cabinet of precious collectibles, so your treasures are out of reach from tiny hands. This way all cabinets can remain the same depth with a continuous crown along the ceiling. Joined oct 19, 2007 · 352 posts.

It is usually about 1.5" The other two pieces remain the same throughout the kitchen. Apply and smooth the caulk then remove the tape.

It can be prevented by nailing the ceiling molding to the ceiling allowing it to float up and down on the wall. There are 2 ways to do this without plastering. Install the cut pieces as well, using wood glue to help hold the joints together, until you reach the uneven area.

The first piece needed is the carrier molding. Hold the pencil at this angle and draw the line from end to end on the molding. Uneven ceilings can create issues in kitchens when it comes to crown or other mouldings that finish out the tops of cabinets.

Want to repaint the white/cream, upgrade to